Fatigue Life Analysis of FSO Anchor Chain with Corrosion Effect

Dewinta Putri Cahyaningtyas, Nur Syahroni, Rudi Walujo Prastianto, Eko Budi Djatmiko, Murdjito Murdjito, Hafizh Muhammad Naufal Shidqi

Abstract


In this study, the authors analyze the fatigue life of the anchor chain used to secure the Gamkonora FSO to the seabed. The objective is to determine the operational lifespan of the anchor chain by considering its fatigue life. The research begins with an analysis of the movement of the Gamkonora FSO under environmental loads in both free-floating and moored conditions to determine the tension in each anchor chain. Next, the anchor chain tension is calculated for various corrosion levels, namely 0%, 5%, 10% and 15%. Subsequently, the tension range and damage ratio values are determined using the T-N curve method based on Palmgren Miner’s failure law, with failure estimation carried out using the rainflow counting method. The numerical modeling results reveal that the largest translational motion behavior of the FSO occurs during heave motion, reaching 1.409 m/m, while the largest rotational motion is observed during roll motion, with a value of 3.463 deg/m when the FSO is fully loaded. The maximum tension recorded in the anchor chain is 1,695.14 kN at heading 90 under 0% corrosion conditions, with a safety factor of 4.53. Furthermore, the cumulative damage value from the T-N curve is obtained, with the largest value recorded as 0.0702. Based on the cumulative damage, the fatigue life of the anchor chain is estimated to be 14.25 years during its operational lifespan.

Keywords


Cumulative Damage; Damage Ratio; Failure; Rainflow Counting; Tension Range; T-N Curve

Full Text:

PDF

References


E. B. Djatmiko, “Perilaku dan Operabilitas Bangunan Laut di Atas Gelombang Acak,” 2012, pp. 1–27.

S. Junianto, Mukhtasor, R. W. Prastianto, and W. Wardhana, “Motion Responses Analysis for Tidal Current Energy Platform: Quad-Spar and Catamaran Types,” China Ocean Eng., vol. 34, no. 5, pp. 677–687, 2020.

K-T. Ma, “Mooring System Engineering for Offshore Structures,” In European University Institute, Issue 2, Gulf Professional Publishing, 2018.

J. J. Soedjono, “Diktat Mata Kuliah Kontruksi Bangunan Laut II,” Jurusan Teknik Kelautan ITS, 1998.

J. J. Soedjono, “Kuliah Perencanaan Sistem Bangunan Laut I,” Jurusan Teknik Kelautan ITS, 1989.

E. B. Djatmiko, “Seakeeping: Perilaku Bangunan Apung di Atas Gelombang,” ITS Press, 2003.

Y. Wu, T. Wang, O. Eide, and K. Haverty, “Governing factor and locations of fatigue damage on mooring lines of floating structures,” Ocean Engineering, vol. 96, pp. 109-124, 2015.

C. Kang, C. Lee, S. H. Jun, and Y. T. Oh, “Fatigue analysis of spread mooring line,” Int. J. Environ. Chem. Geol. Geophys. Eng., vol. 10, no. 5, 2016.

R. W. Prastianto, Ramzi, and Murdjito, “Mooring Analysis of SPAR Type Floating Offshore Wind Turbine in Operation Condition due to Heave, Roll, and Pitch Motions,” IOP Conference Series: Earth and Environmental Science, IOP Publishing, 2019.

IACS, “L5 Computer Software for Onboard Stability Calculations,” pp. 1–12, 2017.

ABS, “Rules for Building and Classing Mobile Offshore Drilling Units,” Houston: American Bureau of Shipping, 2018.

S. K. Chakrabarti, S. K., “Hydrodynamics of Offshore Structures,” In European University Institute (Issue 2), Mid-County Press, 1987.

N. M. Sabana, E. B. Djatmiko, and R. W. Prastianto, “Fatigue Life of Mooring Lines on External Turret Floating LNG for Different Pretension and Water Depth,” IPTEK The Journal for Technology and Science, vol. 30(1), April, 2019.

DNVGL-OS-E301, “Position Mooring.” July. 114, 2015.

API RP 2SK, “Recommended Practice for Design and Analysis of Station Keeping Systems for Floating Structures,” 2005.

S. Junianto, Mukhtasor, R. W. Prastianto, and C. H. Jo, “Effects of demi-hull separation ratios on motion responses of tidal current turbines-loaded catamaran,” Ocean Syst. Eng., vol. 10, no. 1, pp. 87–110, 2020.

A. H. Adaalah, R. W. Prastianto, Murdjito, F. Syalsabila, and M. R. Syarifudin, “Analysis of Mooring Line Tension in Floating Collar Net Cage,”, 6th International Conference on Marine Technology (SENTA 2021), IOP Publishing, 2022.

BKI, “Guidelines for Floating Production Installations,” vol. 3, 2013.

G. Alencar, “A user-friendly tool for fatigue assessment of steel structures according to Eurocode 3. New Trends on Integrity, Reliability and Failure,” July, pp. 1–9, 2016.

DKPU ITS, “Zulu Terminal Marine Conceptual Study,” Project Report, 2023.




DOI: http://dx.doi.org/10.12962/j25481479.v8i2.16942

Refbacks

  • There are currently no refbacks.


Abstracted / Indexed by:
      
  

 

 

 

 

 

P-ISSN: 2541-5972   

E-ISSN: 2548-1479

 

Lisensi Creative Commons

IJMEIR journal published by  Department of Marine Engineering, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember Surabaya Indonesia under licenced Creative Commons Attribution-ShareAlike 4.0 International Licence. Based on https://iptek.its.ac.id/index.php/ijmeir/