Study of Hardening Process of AISI 1045 Steel Material with Variation of Heating Temperature, Media, and Cooling Media Volume for Shaft Application

Heri Setiawan, Cecep Ruskandi, Abdul Latif

Abstract


Shafts are critical components in engines that facilitate power transmission and rotation. AISI 1045 steel is a cheap alternative for shaft manufacturing, but a proper selection of heat treatment parameters is required to optimize its mechanical properties. This research aims to study the process effect of heating temperature, type of cooling media, and volume ratio of cooling media on the hardness and wear of AISI 1045 material. The results show that the kind of cooling media significantly affects hardness and wear, while the heating temperature and cooling media volume ratio are not significant. The heat treatment process at 850°C with water cooling and a ratio of 12:1 resulted in a hardness of 60 HRC and a wear rate of 0.00335 grams. However, further studies on the tempering process and other parameter adjustments are required to achieve optimum performance.


Keywords


Spindle Shaft; AISI 1045 Steel; Heat Treatment; Hardness; Wear;

Full Text:

PDF

References


Sularso and K. Sugara, “Dasar Perancangan Dan Pemilihan Elemen Mesin,” Pap. Knowl. . Towar. a Media Hist. Doc., p. 200, 2014.

V. B. Bhandari, Machine Elements in Mechanical Design 6th Edition. 2018.

E. F. Cone, “ASM Handbook Volume 1: Properties and Selection Irons Steels and High Performance Alloys,” ASM Int., vol. STP 24, pp. 1–24, 1991, doi: 10.1520/STP38736S.

F. R. Sidiq, G. Anggana, and N. Bilqis, “Produk Stationery Tools Box For Office Produk,” Politeknik Manufaktur Bandung, Bandung 2022.

Z. Cai, J. Zhao, and H. Ding, “ASM Handbook Volume 4: Heat Treating,” USA ASM Int., pp. 289–322, 1993, doi: 10.1201/9781315120577.

F. Nurrafi, “MESIN FRAIS FEHLMANN P18S,” Politek. Manufaktur bandung, Bandung 2023.

G. Hultquist and C. Leygraf, “Material Science and Engineering An Introduction,” Mater. Sci. Eng. A, vol. 42, no. 1, p. 181, 1980.

L. Hasya, “TROUBLE REPAIR SPINDLE MESIN FRAIS FEHLMANN P 18 S ( FR10),” Politeknik Manufaktur Bandung, Bandung, 2023.

U. Logostik, “Logistik Politeknik Manufaktur Bandung,” 2022.

A. N. Amalia, “Analisis Pengaruh Perlakuan Panas Hardening Dengan Variasi Temperatur Pemanasan, Waktu Tahan, Dan Media Pendingin Pada Peningkatan Kekerasan Baja AISI 1045 Pada Komponen Axle Shaft,” Skripsi, pp. 1–111, 2018.

A. H. Razak and S. Rasyid, “Pengaruh Perbandingan Berat Media Quenching dengan Berat Spesimen Uji terhadap Sifat Mekanik Baja Karbon Sedang (S45C),” Pros. Semin. Has. Penelit., vol. 2018, pp. 182–187, 2018.

Wegst C.W., Stahlschlüssel 18 edition. 1998.

G. E. Totten, Failure Ananlysis of Heat Treated Steel Components. Ohio: ASM International, 2007.

G. Kraus, STEELS: Heattreatment and Processing Principles. Material Park, Ohio: ASM International, 1990.




DOI: http://dx.doi.org/10.12962/j25481479.v9i3.20957

Refbacks

  • There are currently no refbacks.


Abstracted / Indexed by:
      
  

 

 

 

 

 

P-ISSN: 2541-5972   

E-ISSN: 2548-1479

 

Lisensi Creative Commons

IJMEIR journal published by  Department of Marine Engineering, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember Surabaya Indonesia under licenced Creative Commons Attribution-ShareAlike 4.0 International Licence. Based on https://iptek.its.ac.id/index.php/ijmeir/