Reinforcing Bricks with Natural Fibres: A Review
Abstract
Natural fibres are biomass waste that agriculture generates in abundance. Lacking environmental awareness, biomass waste is often improperly disposed of. This raises environmental concerns. Natural fibres might be used as building materials, such as bricks. This might be a viable alternative for sustainable development. In this study, articles on the use of natural fibres in bricks are reviewed. The purposes were to study their influence on the structural behaviour of fibre-reinforced bricks and to identify their prospects and challenges. Natural fibres were found to reduce the brick's density, drying shrinkage, thermal conductivity, and workability. They boosted the compressive, tensile, flexural, and tensile splitting strengths, as well as the water absorption capacity. Natural fibres can only be used in limited amounts in bricks, usually less than 5%. This prevents significant strength loss and excessive water absorption. This study points out the drawbacks of natural fibres, such as inconsistent properties, dimensional changes, combustibility, decay susceptibility, and microbiological growth susceptibility. These shortcomings should be addressed before commercialising fibre-reinforced bricks. To overcome the problems, natural fibres may need to be carefully screened and treated before being used in bricks.
Keywords
Full Text:
PDFReferences
Harsono, L. T. Mulyantara, A. T. Rizaluddin, A. Nakagawa-izumi, and H. Ohi, "Properties of fibres prepared from oil palm empty fruit bunch for use as corrugating medium and fiberboard," Japan Tappi Journal, vol. 69, pp. 1349-1345, 2015.
A. Abdul Kadir, N. A. Sarani, S. Zulaikha Mokhtar, and M. M. Al Bakri Abdullah, "Physical and mechanical properties by utilizing empty fruit bunch into fired clay brick," in AIP Conference Proceedings, 2017.
S. Ismail and Z. Yaacob, "Properties of laterite brick reinforced with oil palm empty fruit bunch fibres," Pertanika Journal of Science & Technology, vol. 19, pp. 33 – 43, 2011.
C. Arslan, O. Gencel, I. Borazan, M. Sutcu, and E. Erdogmus, "Effect of waste-based micro cellulose fiber as pore maker on characteristics of fired clay bricks," Construction and Building Materials, vol. 300, p. 124298, 2021/09/20/ 2021.
D. W. Gawatre and L. N. Vairagade, "Strength characteristics of different types of bricks," International Journal of Science and Research, vol. 3, pp. 2247–2252, 2014.
S. Ajouguim, S. Talibi, C. Djelal-Dantec, H. Hajjou, M. Waqif, M. Stefanidou, et al., "Effect of Alfa fibers on the mechanical and thermal properties of compacted earth bricks," Materials Today: Proceedings, vol. 37, pp. 4049-4057, 2021.
M. Bouhicha, F. Aouissi, and S. Kenai, "Performance of composite soil reinforced with barley straw," Cement and Concrete Composites, vol. 27, pp. 617-621, 2005.
H. Danso, D. B. Martinson, M. Ali, and J. B. Williams, "Physical, mechanical and durability properties of soil building blocks reinforced with natural fibres," Construction and Building Materials, vol. 101, pp. 797-809, 2015.
K. Ghavami, R. D. Toledo Filho, and N. P. Barbosa, "Behaviour of composite soil reinforced with natural fibres," Cement and Concrete Composites, vol. 21, pp. 39-48, 1999.
I. Bouchefra, F. Z. El Bichri, H. Chehouani, and B. Benhamou, "Mechanical and thermophysical properties of compressed earth brick rienforced by raw and treated doum fibers," Construction and Building Materials, vol. 318, p. 126031, 2022.
A. W. Bruno, D. Gallipoli, and C. Perlot, "Effect of freezing-thawing cycles on the physical and mechanical properties of fired and unfired earth bricks," Journal of Building Engineering, vol. 52, p. 104501, 2022.
P. Zak, T. Ashour, A. Korjenic, S. Korjenic, and W. Wu, "The influence of natural reinforcement fibers, gypsum and cement on compressive strength of earth bricks materials," Construction and Building Materials, vol. 106, pp. 179-188, 2016.
G. Calatan, A. Hegyi, C. Dico, and C. Mircea, "Determining the optimum addition of vegetable materials in adobe bricks," Procedia Technology, vol. 22, pp. 259-265, 2016.
Y. Millogo, J.-C. Morel, J.-E. Aubert, and K. Ghavami, "Experimental analysis of pressed adobe blocks reinforced with hibiscus cannabinus fibers," Construction and Building Materials, vol. 52, pp. 71-78, 2014.
C. Babé, D. K. Kidmo, A. Tom, R. R. N. Mvondo, B. Kola, and N. Djongyang, "Effect of neem (Azadirachta Indica) fibers on mechanical, thermal and durability properties of adobe bricks," Energy Reports, vol. 7, pp. 686-698, 2021.
D. Dominguez-Santos and J. Alberto Moya Bravo, "Structural and mechanical performance of adobe with the addition of high-density polyethylene fibres for the construction of low-rise buildings," Engineering Failure Analysis, vol. 139, p. 106461, 2022.
A. Eslami, H. Mohammadi, and H. Mirabi Banadaki, "Palm fiber as a natural reinforcement for improving the properties of traditional adobe bricks," Construction and Building Materials, vol. 325, p. 126808, 2022.
N. A. Vodounon, C. Kanali, and J. Mwero, "Compressive and flexural strengths of cement stabilized earth bricks reinforced with treated and untreated pineapple leaves fibres," Open Journal of Composite Materials, vol. 8, pp. 145-160, 2018.
V. Sharma, B. M. Marwaha, and H. K. Vinayak, "Enhancing durability of adobe by natural reinforcement for propagating sustainable mud housing," International Journal of Sustainable Built Environment, vol. 5, pp. 141-155, 2016.
I. Kafodya, F. Okonta, and P. Kloukinas, "Role of fiber inclusion in adobe masonry construction," Journal of Building Engineering, vol. 26, p. 100904, 2019.
E. Quagliarini and S. Lenci, "The influence of natural stabilizers and natural fibres on the mechanical properties of ancient Roman adobe bricks," Journal of Cultural Heritage, vol. 11, pp. 309-314, 2010.
F. Parisi, D. Asprone, L. Fenu, and A. Prota, "Experimental characterization of Italian composite adobe bricks reinforced with straw fibers," Composite Structures, vol. 122, pp. 300-307, 2015.
H. Binici, O. Aksogan, and T. Shah, "Investigation of fibre reinforced mud brick as a building material," Construction and Building Materials, vol. 19, pp. 313-318, 2005.
H. Binici, O. Aksogan, M. N. Bodur, E. Akca, and S. Kapur, "Thermal isolation and mechanical properties of fibre reinforced mud bricks as wall materials," Construction and Building Materials, vol. 21, pp. 901-906, 2007.
S. Serrano, C. Barreneche, and L. F. Cabeza, "Use of by-products as additives in adobe bricks: Mechanical properties characterisation," Construction and Building Materials, vol. 108, pp. 105-111, 2016.
E. Olacia, A. L. Pisello, V. Chiodo, S. Maisano, A. Frazzica, and L. F. Cabeza, "Sustainable adobe bricks with seagrass fibres. Mechanical and thermal properties characterization," Construction and Building Materials, vol. 239, p. 117669, 2020.
A. V. Oskouei, M. Afzali, and M. Madadipour, "Experimental investigation on mud bricks reinforced with natural additives under compressive and tensile tests," Construction and Building Materials, vol. 142, pp. 137–147, 2017.
H. Danso, D. Brett Martinson, M. Ali, and J. B. Williams, "Effect of sugarcane bagasse fibre on the strength properties of soil blocks," presented at the First International Conference on Bio-based Building Materials (ICBBM 2015), Clermont-Ferrand, France, 2015.
Ş. Yetgin, Ö. Çavdar, and A. Çavdar, "The effects of the fiber contents on the mechanic properties of the adobes," Construction and Building Materials, vol. 22, pp. 222-227, 2008.
K. AlShuhail, A. Aldawoud, J. Syarif, and I. A. Abdoun, "Enhancing the performance of compressed soil bricks with natural additives: Wood chips and date palm fibers," Construction and Building Materials, vol. 295, p. 123611, 2021.
Z. Lu, Z. Zhao, M. Wang, and W. Jia, "Effects of corn stalk fiber content on properties of biomass brick," Construction and Building Materials, vol. 127, pp. 11-17, 2016.
Z. Lu, M. Wang, and W. Jia, "Effects of compression ratio on water resistant properties of biomass brick," Construction and Building Materials, vol. 127, pp. 784-803, 2016.
Z. Lu, C. Ma, Z. Zhao, W. Jia, and M. Wang, "Effects of hot air drying time on properties of biomass brick," Applied Thermal Engineering, vol. 109, Part A, pp. 487-496, 2016.
M. Wang and Z. Lu, "Study on the hygroscopic performances of poplar wood fiber biomass brick," International Communications in Heat and Mass Transfer, vol. 135, p. 106063, 2022.
M. Wang and Z. Lu, "Thermal and moisture coupling performances of poplar fiber inorganic humidity control brick," Construction and Building Materials, vol. 348, p. 128656, 2022.
S. Zhang, R. Dong, M. Wang, W. Jia, and Z. Lu, "Synthesis mechanisms on waste poplar fiber lightweight biomass bricks," Journal of Cleaner Production, vol. 246, p. 118981, 2020.
C. Juárez, B. Guevara, P. Valdez, and A. Durán-Herrera, "Mechanical properties of natural fibers reinforced sustainable masonry," Construction and Building Materials, vol. 24, pp. 1536-1541, 2010.
R. Kolop, W. I. M. Haziman, and J. W. Eng, "Properties of cement blocks containing high content of oil palm empty fruit bunches (EFB) Fibres," in International Conference on Civil Engineering Practice (ICCE08), Kuantan, Pahang, 2008.
J. H. Ling, Y. T. Lim, W. K. Leong, E. Jusli, and H. T. Sia, "Properties of cement brick with partial replacement of sand and cement with oil palm empty fruit bunches and silica fume," Journal of the Civil Engineering Forum, vol. 5, pp. 289-300, 2019.
J. H. Ling, Y. T. Lim, W. K. Leong, and H. T. Sia, "Utilization of oil palm empty fruit bunch in cement bricks," Journal of Advanced Civil and Environmental Engineering, vol. 4, pp. 1-10, 2021.
J. H. Ling, Y. T. Lim, W. K. Leong, and H. T. Sia, "Effects of adding silica fume and empty fruit bunch to the mix of cement brick," Indonesian Journal of Computing, Engineering, and Design, vol. 3, pp. 19-30, 2021.
K. Kartini, Z. A. Norul Ernida, B. Noor Fazilla, and H. Ahmad Farhan, "Development of lightweight sand-cement bricks using quarry dust, rice husk and kenaf powder for sustainability," International Journal of Civil & Environmental Engineering IJCEE-IJENS, vol. 12, pp. 1–7, 2012.
A. C. Abdullah and C. C. Lee, "Effect of treatments on properties of cement-fiber bricks utilizing rice husk, corncob and coconut coir," Procedia Engineering, vol. 180, pp. 1266-1273, 2017.
A. Micheal and R. R. Moussa, "Investigating the economic and environmental effect of integrating Sugarcane Bagasse (SCB) fibers in cement bricks," Ain Shams Engineering Journal, vol. 12, pp. 3297-3303, 2021.
P. Muñoz, V. Letelier, L. Muñoz, M. A. Bustamante, O. Gencel, and M. Sutcu, "The combined effect of bottom ashes and cellulose fibers on fired clay bricks," Construction and Building Materials, vol. 301, p. 124307, 2021.
A. A. Kadir, N. A. Sarani, N. N. Zaman, and M. M. A. B. Abdullah, "Feasibility study on utilization of palm fibre waste into fired clay brick," in AIP Conference Proceedings 2017.
K. Rashid, E. U. Haq, M. S. Kamran, N. Munir, A. Shahid, and I. Hanif, "Experimental and finite element analysis on thermal conductivity of burnt clay bricks reinforced with fibers," Construction and Building Materials, vol. 221, pp. 190-199, 2019.
A. N. Raut and C. P. Gomez, "Development of thermally efficient fibre-based eco-friendly brick reusing locally available waste materials," Construction and Building Materials, vol. 133, pp. 275-284, 2017.
R. Mahjoub, J. Mohamad Yatim, and A. R. Mohd Sam, "A review of structural performance of oil palm empty fruit bunch fiber in polymer composites," Advances in Materials Science and Engineering, vol. 2013, p. 9, 2013.
H. Danso, D. B. Martinson, M. Ali, and J. Williams, "Effect of fibre aspect ratio on mechanical properties of soil building blocks," Construction and Building Materials, vol. 83, pp. 314-319, 2015.
F. N. A. Abd. Aziz, S. M. Bida, N. A. Mohd Nasir, and M. S. Jaafar, "Mechanical properties of lightweight mortar modified with oil palm fruit fibre and tire crumb," Construction and Building Materials, vol. 73, pp. 544-550, 2014.
P. Rama Rao and G. Ramakrishna, "Experimental investigation mechanical properties of oil palm empty fruit bunch fiber reinforced cement mortar," Materials Today: Proceedings, 2020.
A. N. Raut and C. P. Gomez, "Thermal and mechanical performance of oil palm fiber reinforced mortar utilizing palm oil fly ash as a complementary binder," Construction and Building Materials, vol. 126, pp. 476-483, 2016.
H. Gu, "Tensile behaviours of the coir fibre and related composites after NaOH treatment," Materials & Design, vol. 30, pp. 3931-3934, 2009.
K. J. Vishnu Vardhini, R. Murugan, C. Tamil Selvi, and R. Surjit, "Optimisation of alkali treatment of banana fibres on lignin removal," Indian Journal of Fibre & Textile Research, vol. 41, pp. 156-160, 2016.
C. A. Amaylia and C. C. Lee, "Effect of treatment on Surface Modifier and Water Retention Value (WRV) of natural fiber," Australian Journal of Basic and Applied Sciences, vol. 9, pp. 101-104, 2015.
A. Thakur, K. Senthil, and A. P. Singh, "Evaluation of concrete bricks with crumb rubber and polypropylene fibres under impact loading," Construction and Building Materials, vol. 315, p. 125752, 2022.
J. H. Ling, Y. T. Lim, W. K. Leong, and H. T. Sia, "The advantages and disadvantages of palm oil empty fruit bunch on bricks and mortar," Journal of the Civil Engineering Forum, vol. 8, pp. 193-204, 2022.
S. H. Chang, "An overview of empty fruit bunch from oil palm as feedstock for bio-oil production," Biomass and Bioenergy vol. 62, pp. 174 - 181, 2014.
K. L. Pickering, M. G. A. Efendy, and T. M. Le, "A review of recent developments in natural fibre composites and their mechanical performance," Composites Part A: Applied Science and Manufacturing, vol. 83, pp. 98-112, 2016.
M. R. Sanjay, S. Siengchin, J. Parameswaranpillai, M. Jawaid, C. I. Pruncu, and A. Khan, "A comprehensive review of techniques for natural fibers as reinforcement in composites: Preparation, processing and characterization," Carbohydrate Polymers, vol. 207, pp. 108-121, 2019.
DOI: http://dx.doi.org/10.12962/j20861206.v39i2.19651
Refbacks
- There are currently no refbacks.
Journal of Civil Engineering is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.