Analysis of Influence of Abrasive Material Variation and Spray Pressure Variation in Coating Epoxy of Astm A36 Steel Toward Impact Resistance and Corrosion Rate

Herman Pratikno; Bima Satriya Willy Harsa; Sholihin Sholihin

doi:10.12962/j2580-0914.v4i2.9337

Analysis of Influence of Abrasive Material Variation and Spray Pressure Variation in Coating Epoxy of Astm A36 Steel Toward Impact Resistance and Corrosion Rate

Herman Pratikno, Bima Satriya Willy Harsa, Sholihin Sholihin

Abstract

Corrosion is a decrease in material quality caused by environmental influences. One of the methods commonly used to control corrosion is coating. In the coating process, the use of spray is the better method compared to roll and brush. Before coating is applied, the choice of abrasive material during the sand blasting process can determine the success of the coating. This research was conducted to analyze the effect of variations in abrasive material and spray pressure on the coating process of ASTM A36 steel material on its impact resistance, corrosion rate, and adhesion forces. Variation of abrasive material used were steel grit and silica. The spray pressure variations used were 2.5, 3.5, and 4.5 bar. The result of corrosion rate testing on variation with steel grit abrasive material and spray pressure of 4.5 bar has the lowest corrosion rate, with the value of 0.00124 mm/a. The highest adhesion strength test result of 9.07 MPa was obtained from variations with steel grit abrasive material and spray pressure of 4.5 bar. Impact test result using a variation with steel grit abrasive materials and a spray pressure of 4.5 bar yield the highest value, with the value of 2.287 joules.

Keywords

coating; abrasive material; spray pressure; corrosion; adhession; impact

Full Text:

PDF

References

Chamberlain J., Trethewey KR. 1991. Korosi (Untuk Mahasiswa dan Rekayasawan). Jakarta. PT Gramedia Pustaka Utama.

Gusti, Arvira. 2018. Analisis Pengaruh Material Abrasif dan Variasi Tekanan Sand Basting pada Baja ASTM A36 Terhadap Daya Lekat Coating. Surabaya. ITS.

Debrita, Cicilia. 2017. Analisis Pengaruh Variasi Coating pada Pelat Baja ASTM A36 terhadap Prediksi Laju Korosi, Kekuatan Adhesi, dan Ketahanan Impact. Surabaya. ITS.

Alfin. 2011. Pengaruh Inhibitor Korosi Berbasis Senyawa Fenolik Untuk Proteksi Pipa Baja Karbon Pada Lingkungan 0.5, 1.5, 2.5, 3.5 % NaCl Yang Mengandung Gas CO2. Universitas Indonesia. Depok.

ISO 8501. 2011. “Corrosion Protection of Steel Structures by Painting”. Internasional Organization for Standarization.

ISO 8503. 2012. “Preparation od Steel Substrates before Application of Paints and related Products”. Internasional Organization for Standarization.

ASTM D-4417. 1999. Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel. Annual Book of ASTM Standards.

ASTM 2794 “Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact).

ASTM D4541-2. 2002. Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers.

Wang, J. Heberlein, E. Pfender, and W. Gerberich. 1998. Effect of Nozzle Configuration, Gas Pressure, and Gas Type on Coating Properties in Wire Arc Spray X. Journal of Thermal Spray Technology, Journal of Thermal Spray Technology, Vol. 8 no 4.

DOI: http://dx.doi.org/10.12962%2Fj2580-0914.v4i2.9337

Refbacks

There are currently no refbacks.

dayak777

slot

https://adlersappetiteonline.com/

situs slot 4d

https://tangerang.pks.id/

slot gacor

slot demo

slot demo pg

https://fahamubooks.org/aboutus/

link slot

https://www.refugeeinfobus.com/about-us

slot demo pg

Username
Password
Remember me