Numerical Study of Impeller Trimming on a Centrifugal Pump Test Unit

R. Aurick Nugraha Prawito, Vivien Suphandani Djanali, Alif Arif Wicaksono

Abstract


Centrifugal pumps have an essential role in various industries. Impeller trimming is often performed to optimize the pump performance at a particular operating point. Impeller trimming refers to a reduction in the impeller outer diameter and thus causes a change in the velocity triangle on the impeller of a centrifugal pump. Three-dimensional, unsteady simulations were conducted numerically using moving mesh. This centrifugal pump has a backward-curved impeller with six blades, with an outer diameter of 120 mm and an outlet angle of 10◦ , which will be trimmed to a diameter of 114 mm. Trimming the impeller reduced the outer diameter so that the outlet angle of the relative velocity to the tangential direction, β2, automatically changed according to the blade shape. The simulation was done by varying the pump discharge. The simulation results were compared with the experimental results. The results obtained in this study include quantitative data and qualitative data. Qualitative data was the appearance of velocity profiles, velocity vectors, and pressure contours. Meanwhile, the quantitative data were in the form of suction pressure, discharge pressure, head calculation, and hydraulic power. The comparison of the results of the numerical simulation with the experimental results have the same trend, although the simulation tended to underestimate the head and hydraulic power. A decrease in head and hydraulic power of the pump due to trimming the impeller from the lowest discharge to the highest discharge is as much as 13% to 24%.

Keywords


Backward-curved impeller; centrifugal pump; Computational Fluid Dynamics; impeller trimming

Full Text:

PDF

References


G. Singh and J. W. Mitchell, “Energy savings from pump impeller trimming,” ASHRAE journal, vol. 40, no. 4, p. 60, 1998.

L. Tsang, “A theoretical account of impeller trim ming of the centrifugal pump,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 206, no. 3, pp. 213–214, 1992.

D. G. J. Detert Oude Weme, M. S. van der Schoot, N. P. Kruyt, and E. J. J. van der Zijden, “Prediction of the Effect of Impeller Trimming on the Hydraulic Per formance of Low Specific-Speed Centrifugal Pumps,” Journal of Fluids Engineering, vol. 140, 03 2018. 081202.

W. Guang Li, “Impeller trimming of an industrial centrifugal viscous oil pump,” ADMT Journal, vol. 5, no. 1, pp. –, 2011.

M. Šavar, H. Kozmar, and I. Sutlovi´c, “Improving centrifugal pump efficiency by impeller trimming,” Desalination, vol. 249, no. 2, pp. 654–659, 2009.

X. Qu and L. Wang, “Effects of impeller trimming methods on performances of centrifugal pump,” Journal of Energy Engineering, vol. 142, no. 4, p. 04016008, 2016.

V. S. Djanali, D. S. Wahono, A. A. Wicaksono, and N. Ikhwan, “Numerical and experimental study on a backward impeller of centrifugal pump,” in AIP Conference Proceedings, vol. 1983, p. 020033, AIP Publishing LLC, 2018.

S. Huang, J. Guo, and F. Yang, “Numerical simu lation of 3d unsteady flow in a rotating pump by dynamic mesh technique,” in IOP Conference Series: Materials Science and Engineering, vol. 52, p. 022030, IOP Publishing, 2013.

D. Šlachtiˇc, B. Knížat, and R. Olšiak, “CFD analysis of impeller trimming,” in MATEC Web of Conferences, vol. 328, p. 02009, EDP Sciences, 2020.

P. Zhou, J. Tang, J. Mou, and B. Zhu, “Effect of impeller trimming on performance,” World Pumps, vol. 2016, no. 9, pp. 38–41, 2016.

A. A. Wicaksono, Studi Pengaruh Trimming Impeller Backward Single Curvature 6 Sudu Terhadap Karak teristik Kerja Pompa Sentrifugal FM50. PhD thesis, In stitut Teknologi Sepuluh Nopember, Surabaya




DOI: http://dx.doi.org/10.12962/j25807471.v3i1.9365

Creative Commons License
JMES The International Journal of Mechanical Engineering and Sciences by Lembaga Penelitian dan Pengabdian kepada Masyarakat (LPPM) ITS is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at https://iptek.its.ac.id/index.php/jmes.