Quality Control of Ink Bottles in Efforts to Control Defect Products in Candi Plastik Home Industry

Tri Ilma Sari, Moses Laksono Singgih

Abstract


Quality is one of the most important things in terms of competition between companies. Products that are not of quality will be rejected. Many home industries lose competitiveness in terms of quality, it could be due to inaccurate machining. This causes a lot of product defects. A dozen years this home industry was established, but has not yet met the minimum target defect target of products set by consumers. Quite a lot of products have to be replaced and reworked. So we need a tool to control quality and detect the causes of product defects and then repair the cause. Seven tools are the seven basic tools that are able to solve the quality problems faced by production. Failure Mode Effect Analysis (FMEA) is a tool to detect the causes of production failures. The application of these two tools is expected to be able to control quality, meet the minimum specifications of consumers, detect the causes and correct the causes, increase productivity, reduce losses, and increase consumer confidence. The results of this study are seven tools and FMEA able to control product defects, the percentage of product defects produced by 22.5%, the cause of product defects is caused by 4 factors namely machinery, humans, methods, and raw materials. Whereas based on FMEA analysis, the main cause of product defects is the machine, and proposed control settings of the machine.

Keywords


defective products; FMEA; product qualit; seven Tools

Full Text:

PDF

References


Khomah and E. Siti Rahayu, “Aplikasi Peta Kendali p sebagai Pengendalian Kualitas Karet di PTPN IX Batujamus/Kerjoarum,” Agrar. J. Agribus. Rural Dev. Res., vol. 1, no. 1, pp. 12–24, 2015.

M. S. Hidayatullah Elmas, “Pengendalian Kualitas Dengan Menggunakan Metode Statistical Quality Control (Sqc) Untuk Meminimumkan Produk Gagal Pada Toko Roti Barokah Bakery,” Wiga J. Penelit. Ilmu Ekon., vol. 7, no. 1, pp. 15–22, 2017.

N. B. Puspitasari and A. Martanto, “Penggunaan Fmea Dalam Mengidentifikasi Resiko Kegagalan Proses Produksi Sarung Atm (Alat Tenun Mesin) (Studi Kasus Pt. Asaputex Jaya Tegal),” J@Ti Undip J. Tek. Ind., vol. 9, no. 2, pp. 93–98, 2014.

Andriyani and R. Rumita, “Analisis Upaya Pengendalian Kualitas Kain Dengan Metode Failure Mode and Effect Analysis (Fmea) Pada Mesin Shuttel Proses Weaving PT Tiga Manunggal Synthetic Industries,” J. Tek. Ind. Fak. Tek. Univ. Diponegoro, 2015.

K. Philip, Marketing Management, 14 Edition. Pearson, 2012.

G. David, Managing Quality “The Strategic and Competitive Edge.” New York, London: The Free Press, 1988.

S. Dutta, M. B. Nadaf, and J. N. Mandal, “An Overview on the Use of Waste Plastic Bottles and Fly Ash in Civil Engineering Applications,” Procedia Environ. Sci., vol. 35, pp. 681–691, 2016.

N. Fadlalla, “A cknow ledgem ent,” 2010.

J. Hopewell, R. Dvorak, and E. Kosior, “Plastics recycling: Challenges and opportunities,” Philos. Trans. R. Soc. B Biol. Sci., vol. 364, no. 1526, pp. 2115–2126, 2009.

Iacovidou, A. P. M. Velenturf, and P. Purnell, “Quality of resources: A typology for supporting transitions towards resource efficiency using the single-use plastic bottle as an example,” Sci. Total Environ., vol. 647, pp. 441–448, 2019.

B. Briasco, P. Capra, A. C. Cozzi, B. Mannucci, and P. Perugini, “Packaging evaluation approach to improve cosmetic product safety,” Cosmetics, vol. 3, no. 3, 2016.

Al Fakhri, “Pengaruh Kualitas Terhadap Keputusan Pembelian,” 2010.

R. B. Chase and E. R. Jacob, “2006 Book Chase _Operations Management for competitive advantage.pdf.” pp. 318–371, 2006.




DOI: http://dx.doi.org/10.12962/j23546026.y2020i1.10860

Refbacks

  • There are currently no refbacks.


View my Stat: Click Here

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.