Force Transfer Mechanism of Headed Anchorage Bar in Exterior Beam Column Joint with Finite Element Method and Strut and Tie Model

Ria Ananda, Iswandi Imran

Abstract


In structural concrete, the provisions for anchorage of straight bars and hooks sometimes present detailing problems due to the long development lengths and large bend diameters that are required. Occasionally, the requirements for straight bar anchorage and lap splices cannot be provided within the available dimensions of elements. Hooked bars can be used to shorten anchorage length, but in many cases, the bend of the hook will not fit within the dimensions of a member or the hooks create congestion and make an element difficult to construct. This congestion may lead to high fabrication effort needed and poor concrete placement, resulting in decrease of concrete quality at the joints. An alternative is the use of headed anchorage bar, which allows for extremely small development lengths, that can reduce congestion without compromising the integrity of the structure. As a result, designing and detailing the structure are made easier and more efficient. Headed bars are formed by the attachment of a plate or the forging of an upset bearing surface at the end of a straight reinforcing bar. Such bars are anchored by a combination of bond along the straight bar length and direct bearing at the head. This papers presents strut and tie models explaining force transfer mechanism of headed anchorage bar in exterior beam-column joint under monotonic loads. The proposed model is derived from beam-column joint specimen which have been tested experimentally. Stress and strain generated by modeling the beam column joint with finite element-based program, ATENA 3D. The result of the analysis explaining the behavior of headed anchorage bar is CCT nodes (compression-compression-tension). The model is consists of a strut with the nodal zone at the head for head bearing and a fan-shaped stress field for bond stresses along the development length.

Keywords


headed bar; hooked bar; CCT nodes; compression fields; tension fields; joint shear crack; ATENA 3D

Full Text:

PDF

References


I. Simamora, I. Imran, and F. Yamazaki, “Experimental Study on The Performance of Headed Anchorage Bar in Beam-Column Joints,” in Proceeding the 6th Civil Engineering Conference in Asia Region: Embracing the Future through Sustainability, 2013.

ATENA Program Documentation Part 1. (2007). Theory. Cervenka Consulting, Prague, Czech Republic.

ATENA Program Documentation Part2-2. (2007). User’s Manual for ATENA 3D Version 3.3.2. Cervenka Consulting, Prague, Czech Republic.

ATENA Program Documentation Part4-2. (2007). Tutorial for Program ATENA 3D. Cervenka Consulting, Prague, Czech Republic.

Dewobroto, W. “Simulasi Keruntuhan Balok Beton Bertulang Tanpa Sengkang dengan ADINA”, Prosiding Seminar Nasional “Rekayasa Material dan Konstruksi Beton 2005”, Bandung, 4 Juni

American Concrete Institute. 2014 . Building Code Requirements for Structural Concrete (ACI 318-14). America.

SNI 03-2847-2013. (2013), Tata Cara Perencanaan Struktur beton untuk Bangunan Gedung. Badan Standardisasi Nasional. Jakarta, Indonesia.

Imran, I., & Hendrik, F. (2014), “Perencanaan Lanjut Struktur Beton Bertulang”, Penerbit ITB, Bandung.

Hardjasaputra, H., & Tumilar, S. (2002), “Model Penunjang dan Pengikat (Strut-and-Tie Model) Pada Perancangan Struktur Beton”, Universitas Pelita Harapan, Jakarta.

Kotsovos, Michael D. (2015). Finite Element Modeling of Structural Concrete. CRC Press, New York.

Kwak, Hyou-Gyoung & Filippou F. C. (1990). Finite Element Analysis of Reinforced Concrete Structures Under Monotonic Loads. Department of Civil Engineering. University of California, Barkeley.

MacGregor, J. G., & James K. W. (2006). Reinforced Concrete Mechanics and Design. 4th ed. Prentice Hall, Singapore.

Goto, Yukimasa, “Cracks Formed in Concrete Around Deformed Tension Bars,” Journal of the American Concrete Institute, Proceedings Vol. 68, Detroit, Michigan, April 1971.

Dilger, W.H. and Ghali, A., “Double-Headed Studs as Ties in Concrete,” Concrete International, Vol. 19, No.6, pg. 59-66, Detroit, Michigan, June 1997.

Mains, R.M., “Measurement of the Distribution of Tensile and Bond Stresses Along Reinforcing Bars,” Journal of the American Concrete Institute, Proceedings, Detroit, Michigan, November 1951.

Chun, S.C. & Kim, D.Y. (2004). Evaluation of Mechanical Anchorage of Reinforcement by Exterior Beam-Column Joint Experiments. Vancouver.

DeVries, R.A. (1996). Anchorage of Headed Reinforcement in Concrete. Texas: The University of Texas at Austin.

R. Park and T. Paulay . 1975 . Reinforced Concrete Structures . Department of Civil Engineering . University of Canterbury . Christchurch . New Zealand.

Thompson, M., Jirsa, J.O., Breen, J.E. & Klingner, R.E. (2002). Anchorage Behavior of Headed Reinforcement: Literature Review. Texas: Center for Transportation Research Bureau of Engineering Research The University of Texas at Austin.

Thompson, M.K., Jirsa, J.O. & Breen, J E. (2006). Behavior and Capacity of Headed Reinforcement. ACI Structural Jurnal, Volume 103.

Wallace, J.W. (1996). Use of Mechanically Anchored Bars in Exterior Beam-Column Joints Subjected to Seismic Load, LA: Department of Civil Engineering University of California.

Wallace, J.W. & McConnell, S.W. (1995). Use of Headed Reinforcement in Beam-Column Joints.

Chun, S.C. & Hong, S.G. (2009). Strut-and-Tie Models for Headed Bar Development in C-C-T Nodes. ACI Structural Journal, Volume 106.




DOI: http://dx.doi.org/10.12962/j23546026.y2017i6.3266

Refbacks

  • There are currently no refbacks.


View my Stat: Click Here

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.