Technical Study of Ship Plate Firing Process Time with Variation of Deformation Values

Sinung Widiyanto, Didik Hardianto, Tri Agung Kristiyono, Bagus Kusuma Aditya, Safriudin Rifandi

Abstract


In the process of shipbuilding production and repair, deformation is sometimes encountered due to several factors, starting from load pressure, pulling, lifting, and welding processes. A fairing process is carried out to overcome the plate deformation, in which the plate is heated and cooled simultaneously. The method used in this research is direct time measurement during the fairing process on test plate specimens with variations in the depth of deformation curvature. The data obtained, processed, and analyzed to obtain an estimate of the fairing processing time the longer the fairing process takes, following the equation Y = 41.285X + 530.94, where X is the deformation angle, and Y is the estimation fairing processing time area per half square meter.


Keywords


Deformation; Firing; Time Estimation

Full Text:

PDF

References


N. R. Mandal, Ship construction and welding. Springer, 2017.

E. Turan, T. Koçal, and K. Ünlügençoğlu, “Welding technologies in shipbuilding industry,” Tojsat, vol. 1, no. 4, pp. 24–30, 2011.

Y. Hashiba, K. Sasaki, T. Kasuya, T. Inoue, and Y. Funatsu, “Development of welding materials for high heat input welding compatible with thick steel plates of 460 MPa yield point class for very large container ships,” Welding in the World, vol. 54, pp. R35–R41, 2010.

S. Imai, “Recent progress and future trends for shipbuilding steel,” Welding International, vol. 22, no. 11, pp. 755–761, 2008.

H. M. Wang, H. X. Zhao, Y. J. Dai, and X. S. Rui, “Experimental Research on Effect of Hot Works on Mechanical Performance of Ship Steel Plate,” Adv Mat Res, vol. 311, pp. 1859–1862, 2011.

A. Nair, K. Sivaprasad, and C. G. Nandakumar, “Crack assessment criteria for ship hull structure based on ship operational life,” Cogent Eng, vol. 4, no. 1, p. 1345044, 2017.

M. Eisawy, “Deformations of ship sections during fabrication, causes and remedies,” 2021.

W. Fricke and O. Feltz, “Consideration of influence factors between small‐scale specimens and large components on the fatigue strength of thin‐plated block joints in shipbuilding,” Fatigue Fract Eng Mater Struct, vol. 36, no. 12, pp. 1223–1231, 2013.

M. Kang, J. Seo, and H. Chung, “Ship block assembly sequence planning considering productivity and welding deformation,” International Journal of Naval Architecture and Ocean Engineering, vol. 10, no. 4, pp. 450–457, 2018.

T. D. Huang, P. Dong, L. DeCan, D. Harwig, and R. Kumar, “Fabrication and engineering technology for lightweight ship structures, part 1: distortions and residual stresses in panel fabrication,” Journal of Ship Production, vol. 20, no. 01, pp. 43–59, 2004.

N. A. McPherson, “Thin plate distortion—the ongoing problem in shipbuilding,” Journal of ship production, vol. 23, no. 02, pp. 94–117, 2007.

N. Ma, D. Deng, N. Osawa, S. Rashed, H. Murakawa, and Y. Ueda, Welding deformation and residual stress prevention. Butterworth-Heinemann, 2022.

Y.-F. Hu, K.-F. Chung, H. Ban, and D. A. Nethercot, “Investigations into residual stresses in S690 cold-formed circular hollow sections due to transverse bending and longitudinal welding,” Eng Struct, vol. 219, p. 110911, 2020.

M. Abambres and W.-M. Quach, “Residual stresses in steel members: a review of available analytical expressions,” International Journal of Structural Integrity, vol. 7, no. 1, pp. 70–94, 2016.

N. Ma, D. Deng, N. Osawa, S. Rashed, H. Murakawa, and Y. Ueda, Welding deformation and residual stress prevention. Butterworth-Heinemann, 2022.

Y. Qiu, W. Shen, R. Yan, L. Xu, and E. Liu, “Fatigue reliability evaluation of thin plate welded joints considering initial welding deformation,” Ocean Engineering, vol. 236, p. 109440, 2021.

D. J. Eyres and G. J. Bruce, Ship construction. Butterworth-Heinemann, 2012.

B. Das and P. Biswas, “A review of plate forming by line heating,” Journal of Ship Production and Design, vol. 34, no. 02, pp. 155–167, 2018.

J. Zhao, “Industrial reheating furnaces: A review of energy efficiency assessments, waste heat recovery potentials, heating process characteristics and perspectives for steel industry,” Process Safety and Environmental Protection, vol. 147, pp. 1209–1228, 2021.

F. Adriansyah and N. Y. Nugroho, “Perubahan Sifat Fisik Dan Mekanik Pada Pelat Grade A Yang Mengalami Fairing Pasca Terjadinya Kebakaran Di Kapal,” Prosiding Seminakel, pp. 87–94, 2019.




DOI: http://dx.doi.org/10.12962/j23378557.v10i1.a18594

Refbacks

  • There are currently no refbacks.


Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License. IPTEK The Journal of Engineering published by Pusat Publikasi Ilmiah, Institut Teknologi Sepuluh Nopember. 

 

Please contact us for order or further information at: email: iptek.joe[at]gmail.com Fax/Telp: 031 5992945. Editorial Office Address: Pusat Riset Building 6th floor, ITS Campus, Sukolilo, Surabaya 60111, Indonesia.